Adaptor RGB / CGA / EGA / YUV to VGA
-
Produs:Nou, Certificat de garanție 12 luni
-
Numar articol:136159178
-
Disponibilitate:Indisponibil
-
Preț:200,00 Lei
-
Anuntul a expirat la:24.11.2014, 10:51
-
Ai o nelamurire?
-
Vandut de:
-
Vinde si tu:Pune in vanzare un produs ca acesta
-
Optiuni:
Descriere
Vânzatorul este direct răspunzator pentru produsul afișat în această pagină.
Disponibilitate: Indisponibil - Vezi produse similare
Specificatii
Interfaces:
5V IN(P7, P9)
VGA OUT(P4)
VGA IN(P10), RGBS(P3, P11)
YPbPr(P2)
Input: DC 5V /2A.
Output RGBS,RGBHV,YPbPr
Input RGBS Support: 15KHz,24KHz,31KHz horizontal signal
autoscan
Input RGBHV Support:31K horizontal signal
Input YPbPr Support: 480i-60, 576i-50, 1080i-50, 1080i-60, 480p-60,
576p-60, 720p-50, 720p-60, 1080p-50, 1080p-60 autoscan Input red
green blue can be adjusted by 500 ohm adjuster.
VGA output resolution 640X480,800X600,1024X768,1360X768
Specification:
Supports CGA/EGA/VGA/YUV Component Signal Input
Supports VGA Output (640 x 480, 800 x 600, 1024 x 768, 1360 x
768)
CGA/EGA/VGA signal auto scan (15KHz, 24KHz, 31KHz)
YUV Component signal auto scan (480i, 576i, 720i, 1080i, 480p,
576p, 720p, 1080p)
On Screen Display (English and Chinese)
Supports image position control & image zoom control
True digital 24-bit A/D converter for true 16.7-million color
conversion.
Supports ALL types of VGA monitors (CRT, LCD, PDP, Projector,
etc)
Input Power
5VDC +/- 0.5v (2A)
P7 or P9
Input signal
CGA/EGA
14.5kHz - 16.5kHz
23.5kHz - 25.5kHz
30.5kHz - 32.5kHz
Auto scan
P3 or P11 or P10
RGBHV
30.5kHz - 32.5kHz
Auto scan
P10 or P11
VGA
30.5kHz - 32.5kHz
Auto scan
P10 or P11
Ypbpr
480p,576p,720p,1080p
Auto scan
P2
Ycbcr
480i,576i,720i,1080i
Auto scan
P2
Output signal
VGA
640*480,800*600
1024*768,1360*768
P4 and P13
User controls
Input Switch, Image Zoom, Image Position,
Output Resolution ,R\G\B gain adjust.
Menu Key
R\G\B VR
MENU CONTROL
- “MENU” open OSD menu, and enter.
- “UP” up and increase.
- “DOWN/AUTO” down and reduce.
Press this key: auto scan CGA/EGA signal
Press this key over 5 second and release: reset system
** (this operation is invalid when you open OSD menu)
- “SW” switch input signal Ypbpr/RGBS/RGBHV.
** (this operation is invalid when you open OSD menu)
- “Clamp sp” & “Clamp” please don’t adjust this button, except the
monitor has black item or picture discoloration.
- For more functions control, please look at OSD to operate.
FAQ
No signal on you monitor
-please check the input and output cables, make sure all cables are
connected. And make sure power is on.
The monitor says “No signal”
-please press “SW” to switch input signal.
Input not supports
-when your monitor displays “input not supports”, maybe you need
change to low resolution.
Please press “DOWN/AUTO” over 5 second and release. Reset
resolution to 800*600.
Image not full on you screen
-please enter menu to adjust image position and zoom.
Image shake or freeze
-please press “DOWN/AUTO”, system will auto scan input signal and
restore image.
Have black item on screen, or all screen too black, or picture
discoloration
-please adjust “Clamp sp” and “Clamp st”, please keep “Clamp st”
less than “Clamp sp”.
-we suggest “Clamp st” SET “03” , “Clamp sp” SET “04”.
Image color not right
-please adjust R\G\B VR.
Modalitati de livrare si plata
LIVRARE
In Bucuresti
-
- Predare personala - Sector 6 in max. 2 zile lucratoare
PLATA
- - La predare
- - Ramburs
Politica de retur
- - Produsul nu se poate returna.