Numar articol: 178127901
Pune in
vanzare un produs ca acesta
Programator profesional de chei BMW EWS Editor v3.2.0, calitate A
Cost unic de transport la toate comenzile acestui vanzator
Disponibilitate:
In stoc
1 disponibil
Produs:
Nou, Certificat de garanție 6 luni
Politica de retur:
Acest produs poate fi returnat in 14 zile
Detalii
Plata:
- La predare
- Ramburs
- Avans
Descriere
Raporteaza produsVânzatorul este direct răspunzator pentru produsul afișat în această pagină.
Specificatii
Product Description
1. EWS Editor Version 3.2.0 B For
BMW is designed to work with factory anti-theft system
(immobilizer) EWS.
2. Immobilizer EWS has been installed on the BMW AG vehicles since 1996.
2. Immobilizer EWS has been installed on the BMW AG vehicles since 1996.
EWS Editor Version 3.2.0 B For BMW
Software Version: V3.2.0
Notice:
1. Selecting wrong test point
you may damage or break EWS3 unit
2. PCB of EWS3 unit is covered
with non-conductive compound, it may lead to poor contact of probe
with test point on the PCB of EWS3 unit, and you will be unable to
connect to EWS3 unit.
Description:
This device is designed to work
with factory anti-theft system (immobilizer) EWS. Immobilizer EWS
has been installed on the BMW AG vehicles since 1996. Cars such as
BMW 3 series (E46), 5 series (E39), 7 series (E38), X3 (E83), X5
(E53), Z4 (E85) and other vehicles of BMW AG - MiniCooper, Rover
75, Range Rover are equipped with this system.
USB
interface:
No AC/DC adaptor
required
All modifications of factory
immobilizers are supported: EWS1, EWS2, EWS3, EWS3+
Reading and writing of EWS3 and
EWS3+ via k-line
Automatic version determination
of EWS via reading the memory dump
Adding new keys
Adding used keys (if key’s
password is available)
Resetting used keys into a
“new” state (if key’s password is available)
Recovery of key's
synchronization (matching keys)
Blocking and releasing vehicle
access via the specific key
Recovering of coding data
(vehicle's specific information)
Changing EWS parameters
(product number, date of manufacturing, etc)
Resetting used EWS3 (loading
default values)
Changing VIN number which is
contained in EWS unit
Changing VIN number which is
contained in key (since 1998)
Changing mileage in EWS
(contained in EWS since 1998 and on)
Changing mileage in key
(contained in key since 1998 and on)
Software creates log-file of
read and written keys, which helps to exclude the error of casual
blocking key with password, etc.
Possibility of control and
recovery of variable part of matching code for EWS and engine
control unit DME/DDE
Configuring new transponders
PCF7930 and PCF7935 to work with EWS unit.
Supports FSU (Firmware Secure
Update) from Internet.Except processors with mask set D47J. EWS
unit equipped with this processor has read protection, attempt of
reading the processor with this mask set results EEPROM data
loss.
To recover the data in EWS3
unit with processor (D47J) use the function [ Reset to factory
defaults ]
Supported
Cars:
3 series (E46)
5 series (E39)
7 series (Е38)
X3 (E83)
Х5 (Е53)
Z4 (E85)
Range Rover Vogue
Rover 75
Mini Cooper
Checking of MOTOROLA processor
mask set which is used in some EWS units. Before proceed to reading
of EWS data using the function [ EWS Read ]
Read the marking
(maskset) plotted on processor (Picture):
1. Mask set D47J -old versions
of EWS1, EWS2 and EWS3 hw:2 sw:5. Refer to #Recovering of
EWS
2. Mask set D46J -new versions
of EWS3 and EWS3+. This processor does not contain
unpleasant
Driver
Installation:
1. Start E file
2. Select installation path.
The default path is C: Program Files AvtoTools
EWS_Editor
3. Please connect device to
USB
4. Install drivers from folder
C:Program FilesAvtoTools EWS_EditorDrivers Reading EWS
5. Unplug and detach EWS3 unit
from the car. Attaching points of EWS3 unit can be found in
BM
6. Take the plastic case off
from EWS3
7. Connect EWS3 to the socket
of the cable for reading/writing EWS3
8. Reassure that in EWS Editor
programme type of EWS is switched to Auto
9. In EWS Editor programme
select [ Read EWS ] function
10. Programme tries to read
contents of EWS3 four times, meantime you must touch test point on
the PCB (printed circuit board) of EWS3 with probe (see picture
below), hold it on the test point untill reading procedure
starts.
11. If the connection
established successfully, progress bar appears:
12. Remove the probe off the
PCB
Writing
EWS:
1. Connect EWS3 to the socket
of the cable for reading/writing EWS3
2. Perform all the necessary
changes
3. Select [ Save EWS ] function
in EWS Editor programme
Galerie foto
Modalitati de livrare si plata
LIVRARE
In Cluj-Napoca
-
- Predare personala in max. 1 zi lucratoare
-
- Prin Curier rapid - 24 Lei in max. 2 zile lucratoare
In Romania:
-
- Prin Curier rapid - 24 Lei in max. 2 zile lucratoare
PLATA
- - La predare
- - Ramburs
- - Avans
Politica de retur
- - Produsul se poate returna in maxim 14 zile lucratoare
- - Metoda de retur: Ramburs contravaloare produs
- - Costul transportului va fi suportat de catre cumparator
- - Alte detalii: Retur acceptat in conditiile Garantiei de Livrare
Optiunea ta
Programator profesional de chei BMW EWS Editor v3.2.0, calitate A