Switch Cisco Catalyst 3560 PoE 48x 10/100 + 4x 1000 SFP, WS-C3560-48PS-S

Switch Cisco Catalyst 3560 PoE 48x 10/100 + 4x 1000 SFP, WS-C3560-48PS-S

Model

Brand

CISCO

Series

CATALYST 3560

Model

WS-C3560-48PS-S

Spec

StandardsIEEE 802.1s
IEEE 802.1w
IEEE 802.1x
IEEE 802.3ad
IEEE 802.3af
IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p CoS Prioritization
IEEE 802.1Q VLAN
IEEE 802.3 10BASE-T specification
IEEE 802.3u 100BASE-TX specification
IEEE 802.3ab 1000BASE-T specification
IEEE 802.3z 1000BASE-X specification
1000BASE-X (SFP)
1000BASE-SX
1000BASE-LX/LH
1000BASE-ZX
1000BASE-CWDM SFP 1470 nm
1000BASE-CWDM SFP 1490 nm
1000BASE-CWDM SFP 1510 nm
1000BASE-CWDM SFP 1530 nm
1000BASE-CWDM SFP 1550 nm
1000BASE-CWDM SFP 1570 nm
1000BASE-CWDM SFP 1590 nm
1000BASE-CWDM SFP 1610 nm
RMON I and II standards
SNMPv1, SNMPv2c, and SNMPv3Jumbo FramesUp to 1546 bytesPrimary Ports48 Ethernet 10/100 ports with PoE and 4 SFP-based Gigabit Ethernet portsPrimary Port Speed10/100Mbps + 1000MbpsMAC Address TableUp to 12,000Buffer Memory128 MB DRAM
16-MB Flash memorySecurityIEEE 802.1x allows dynamic, port-based security, providing user authentication.
IEEE 802.1x with VLAN assignment allows a dynamic VLAN assignment for a specific user regardless of where the user is connected.
IEEE 802.1x with voice VLAN permits an IP phone to access the voice VLAN irrespective of the authorized or unauthorized state of the port.
IEEE 802.1x and port security are provided to authenticate the port and manage network access for all MAC addresses, including those of the client.
IEEE 802.1x with an ACL assignment allows for specific identity-based security policies regardless of where the user is connected.
IEEE 802.1x with Guest VLAN allows guests without 802.1x clients to have limited network access on the guest VLAN.
CISCO security VLAN ACLs (VACLs) on all VLANs prevent unauthorized data flows from being bridged within VLANs.
CISCO standard and extended IP security router ACLs (RACLs) define security policies on routed interfaces for control- and data-plane traffic.
Port-based ACLs (PACLs) for Layer 2 interfaces allow application of security policies on individual switch ports.
Unicast MAC filtering prevents the forwarding of any type of packet with a matching MAC address.
Unknown unicast and multicast port blocking allows tight control by filtering packets that the switch has not already learned how to forward.
SSHv2, Kerberos, and SNMPv3 provide network security by encrypting administrator traffic during Telnet and SNMP sessions. SSHv2, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic software image because of U.S. export restrictions.
Private VLAN provides security and isolation between switch ports, helping ensure that users cannot snoop on other users' traffic.
Bidirectional data support on the Switched Port Analyzer (SPAN) port allows the CISCO Secure Intrusion Detection System (IDS) to take action when an intruder is detected.Cabling10BASE-T ports: RJ-45 connectors, two-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
10BASE-T PoE ports: RJ-45 connectors, two-pair Category 3, 4, or 5 UTP cabling power pins 1,2 (negative) and 3,6 (positive)
100BASE-TX ports: RJ-45 connectors, two-pair Category 5 UTP cabling
100BASE-TX PoE ports: RJ-45 connectors, two-pair Category 5 UTP cabling, power on pins 1,2 (negative) and 3,6 (positive)
1000BASE-T ports: RJ-45 connectors, four-pair Category 5 UTP cabling
1000BASE-T SFP-based ports: RJ-45 connectors, four-pair Category 5 UTP cabling
1000BASE-SX, -LX/LH, -ZX, and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber)
CISCO Catalyst 3560 SFP Interconnect Cable: two-pair shielded cabling, 50 cm
Management console port: RJ-45-to-DB-9 cable for PC connections; for terminal connections, use RJ-45- to-DB-25 female data-terminal-equipment (DTE) adaptor (can be ordered separately from CISCO; part number ACS-DSBUASYN=)LEDsPer-port status LEDs: Link integrity, disabled, activity, speed, full-duplex indications, PoE applied, PoE error, and PoE disabled indications
System-status LEDs: System, RPS, link status, link duplex, link speed, and PoE indicationsVLAN SupportYesPower100–240 VAC (autoranging), 5.5–2.8A, 50–60 HzDimensions17.5" x 14.9" x 1.7"Weight13.2 lbs.Temperature0ºC to 45ºC (32ºF to 113ºF)Humidity10 to 85% (noncondensing)

Features

Features1RU fixed-configuration, multilayer switch
Enterprise-class intelligent services delivered to the network edge
IEEE 802.3af and CISCO prestandard Power over Ethernet
IP Base license (formerly SMI) installed
Basic RIP and static routing, upgradeable to full dynamic IP routing
Advanced QoS
Granular Rate Limiting